[Prev][Next][Index][Thread]
Web page update
----------
From: D.C. Cox [SMTP:DR.RESONANCE-at-next-wave-dot-net]
Sent: Wednesday, March 11, 1998 1:28 PM
To: Tesla List
Subject: Re: Web page update
to: Bill
Thanks for the update Bill -- I also noted Mark R's posting on this matter.
Good luck with your work on this project.
DR.RESONANCE-at-next-wave-dot-net
----------
> From: Tesla List <tesla-at-pupman-dot-com>
> To: 'Tesla List' <tesla-at-pupman-dot-com>
> Subject: Web page update
> Date: Tuesday, March 10, 1998 9:56 PM
>
>
> ----------
> From: Wysock, William C. [SMTP:Wysock-at-courier8.aero-dot-org]
> Sent: Tuesday, March 10, 1998 7:47 AM
> To: Tesla List
> Cc: ttr
> Subject: RE: Web page update
>
>
> To D.C.,
>
> The primary of the Master Oscillator is made of two single,
> parallel connected turns, wound around the circumference
> of the outer-most helical layer of secondary turns (this is
> the layer that contains 15 turns at a 20 foot diameter, and is
> 30 inches high. The primary conductors are 750 MCM
> welding cable, as are the inter-connect cables between
> the tank capacitor bank and rotary gap. These are also
> double conductors. The ground connection is to the lower
> most secondary coil turn at the outside layer. The secondary
> will be made from fine stranded, PVC insulated #2 AWG cable.
> I had not made this clear in that illustration.
> Thank you for the question.
>
> Bill Wysock.
> ----------
> From: Tesla List
> To: Tesla List
> Subject: Web page update
> Date: Monday, March 09, 1998 9:44PM
>
>
> ----------
> From: D.C. Cox [SMTP:DR.RESONANCE-at-next-wave-dot-net]
> Sent: Monday, March 09, 1998 6:56 PM
> To: Tesla List
> Subject: Re: Web page update
>
> to: Bill
>
> Sounds like a neat project. Are you applying the traditional HV from the
> xmfr-cap-RSG between the outermost turn and a tap on a more innermost
> turn?? Did you plan on using perhaps 20-60 turns of copper tubing or
using
> some type of welding cable for your pri-sec driver coil?
>
> DR.RESONANCE-at-next-wave-dot-net
>
>
>
> > From: Wysock, William C. [SMTP:Wysock-at-courier8.aero-dot-org]
> > Sent: Monday, March 09, 1998 10:51 AM
>
> > For many months now, the references to the "13M Story"
> > have not had images (figures 1 thru 19) at the end of the
> > article, on my web site. They are posted now.
> <snip>
> > The outer-most winding of the
> > secondary is connected to ground, and the center-most winding
> > turn, is the high voltage output of this system, which drives into
> > the extra coil.
> >
> > This system is at present, under preliminary construction. It
> > encompasses the attributes of Tesla's early designs, as well as
> > what is [speculated] Tesla accomplished in his final design at
> > Wardenclyffe.
> <snip>
> > Before a full-scale Model 14M is built, I plan to construct a 1/10
> > scale model, to prove my hypothisis of design. I will share the
> > results of these investigations here, on the Tesla List.
> >
> > Bill Wysock.
> > ___________________________
> > Tesla Technology Research
>
>