Welcome Back!
Jim Mora
-----Original Message-----
From: tesla-bounces@xxxxxxxxxx [mailto:tesla-bounces@xxxxxxxxxx] On
Behalf
Of DC Cox
Sent: Thursday, January 29, 2009 8:56 PM
To: Tesla Coil Mailing List
Subject: Re: [TCML] Spark gaps, Solid state switches and diodes
If you want a quck and inexpensive fix try my hyperbaric sparkgap.
At this
power level perhaps two in series, but try one first. The vac. cleaner
motors are nearly or sometimes free at large
vac cleaner repair shops. Plbg fittings from local large hardware store
(usually brass fittings), and some 3/4" copper pipe (Home Depot).
You should disconnect your power xmfrs and test all individually to
be sure
one hasn't died.
The SISG gaps also provide high performance, but at a price.
Dr. Resonance
On Thu, Jan 29, 2009 at 8:46 PM, Stephen Hiscock
<stephenhiscock@xxxxxxxxx>wrote:
Hey guys, my name is Stephen, I've just joined this email group.
I work as an electrical Engineer and I've been playing with Tesla Coils
and
High voltage for about 15 years or so, and built a fairly powerful
Tesla
coil about 10 years that made over 1 metre (3-4 feet ) sparks.
It was just Neon Sign powered (I had 6 in parallel) and had a
conventional
spark gap, but it never performed as well as I would like. I fired
it up
the
other night after dusting it off (it had been in my garage for a bout 5
years), and it performed dismally only getting about 1-2 foot
sparks. I
played with the spark gaps etc and got it performing a bit better, but
nothing like it used to go.
I'm thinking that I'm wasting a lot of energy in my spark gap. in
fact tow
nails hammer into wood seemed to perform the best (quenching
issues?) So
I
went online and after a while came across Terry Fritz's plan for a
solid
state spark gap, but his plan only seemed to be for a relatively low
powered
MOT tesla coil. (a few hundred watts)
I'm wondering if anyone who has had first hand experience with these
solid
state spark gaps (SISG) could help me answer a few questions
* My transformers put out 15,000 Volts at 30mA each x 5 (or 6 if the
fuse
doesn't blow ;-) ) so how many will SISG's will I need
* how reliable will his general design be with my coil. (obviously I
will
need more in series - but will I need to parallel them as well??
* Is there an easy way / simply formula to calculate how much
current will
be flowing peak? (800A or 8000A) - depends on resistance or
capacitance or
inductance? - I currently don't have an oscilloscope at home I can use.
* How much power gets wasted in the reverse diodes - normally the
voltage
drop across a diode is 0.7 volts - so does that mean if I'm getting
1000A
peak average in the primary I will be wasting about 700 watts as heat
across
the devices and possibly more depending on how many devices I have?
or am
I
missing something? - this would seem worse than the conventional gap
- but
everyone seems to rave about the performance of SISG and DRSSTC coils.
perhaps its about peak energy levels (not average) and then 700 peak
watts
compared to 15MW peak energy is not much?
I think I just answered my own question. ;-)
Sorry for so many questions, but you guys seem to like answering
questions
- and I've been enjoying the discussion - so hopefully I've added
something
more to chat about.
so to be simple - how easy will it be to scale his design (SISG) to my
coil
or will most components need to be upgraded.
Stephen
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla