[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [TCML] Sudden and unexplained destructive racing spark flashovers



I've found your elevation estimates to be right on the money for every disruptive coil that I've built but I've noticed that solid state coil builders typically use couplings greater than your upper limits. Have you seen the same thing in your solid
state coil designs?

Dave

At 09:04 AM 7/5/2009, you wrote:
I'm just reporting from practical experience in coil building.

If you exceed 0.14 in classic type coils, especially around 0.18 and above,
racing sparks will occur.

There is no reason to exceed this coupling value.  If you do your output
sparks will diminish in length, not grow.

I've attached a flexible shaft coupling to the base of various sec coils and
dynamically elevated and lowered them while the coil is running.  Various
size coils, 4" dia to 24 inch dia.  In all case max spark length is achieved
around 0.12 to 0.14 range.  I've carefully measured the k value at the
setting that we achieved the long spark length for a given coil.

Oddly, it appears to be nearly a linear relationship.  A 24" dia sec
performs best with 9" of elevation.  A 18" dia. sec performs best with 6.5
inches of elevation.  9" dia sec works best with 3.25" of elevation.

At around 0.18 to 0.2 range most coils started to exhibit signs of excessive
corona and occassional flashovers.  I've repeated these experiments with
coils sizes ranging from 4" to 24 inch dia and the results seem to be the
same.  Excessive coupling produces diminished output spark lengths.
Carefull measurements with oscopes indicated the frequencies were starting
to split indicating power was being wasted by not going into the fundamental
resonant freq of the sec inductor.

Dr. Resonance




On Sun, Jul 5, 2009 at 3:15 AM, Dex Dexter <dexterlabs@xxxxxxxxxxx> wrote:

> It's an experimental fact that too high coupling can be the cause of
> flashovers and racing sparks but...The point of max potential is at the
> terminal (top load) of the secondary in 1/4 wave resonance coils.Typical
> couplings used (0.1-0.2 range) can be hardly  high enough for the point of
> max potential to be shifted somewhere else.Perhaps you are referring to
> increased secondary local voltage gradients vs higher coupling
> instead?That's a different thing and more possible to occur I think.
>
>
> Dex
>
>
> --- resonance@xxxxxxxxxxxx wrote:
>
> From: DC Cox <resonance@xxxxxxxxxxxx>
> To: Tesla Coil Mailing List <tesla@xxxxxxxxxx>
> Cc:
> Subject: Re: [TCML] Sudden and unexplained destructive racing spark
> flashovers
> Date: Mon, 29 Jun 2009 20:19:02 -0700
>
> Over coupling is one cause of racing sparks.  It produces more than one HV
> point near the top 1/4 of the coil which can cause local ionization and
> eventual flashover in this area.
>
>
>
> Dr. Resonance
>
>
>
>
>
>
> _____________________________________________________________
> Washington DC's Largest FREE Email service. ---> http://www.DCemail.com<http://www.dcemail.com/>---> A Washington Online Community Member --->
> http://www.DCpages.com <http://www.dcpages.com/>
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
>
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla

_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla