[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [TCML] microbrute DRSSTC

To: Tesla Coil Mailing List <tesla@xxxxxxxxxx>
Subject: Re: [TCML] microbrute DRSSTC
From: W5als <w5als@xxxxxxxxx>
Date: Fri, 28 Dec 2012 16:23:39 -0600
Delivered-to: teslaarchive@xxxxxxxxxx
Delivered-to: tesla@xxxxxxxxxx
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=yahoo.com; s=s1024; t=1356733430; bh=xa+qQCD/x3xOHh9B1ExJa7F+JjMSEDRJy2qguXBrs70=; h=X-Yahoo-Newman-Id:X-Yahoo-Newman-Property:X-YMail-OSG:X-Yahoo-SMTP:Received:Subject:References:From:Content-Type:X-Mailer:In-Reply-To:Message-Id:Date:To:Content-Transfer-Encoding:Mime-Version; b=sruIuXfCt4UgY6PHBiHWYGRsr+sy1fX7yzsjywiNRse3sMm3vV1Uq8hJKyHd+QXmsf2ZUTd2Cfobaj85NCFa8Qz7aCR8SmtFylESKJnHFtjfThS3zM4Bsct9bb2/lrXDKX188CyYdkm/rd5ajEBqbJmXUN1JC+MOR8Fvkr0G0f0=
In-reply-to: <50DE019B.5020709@xxxxxxxxxxxxxx>
List-archive: <http://www.pupman.com/pipermail/tesla>
List-help: <mailto:tesla-request@pupman.com?subject=help>
List-id: Tesla Coil Mailing List <tesla.pupman.com>
List-post: <mailto:tesla@pupman.com>
List-subscribe: <http://www.pupman.com/mailman/listinfo/tesla>, <mailto:tesla-request@pupman.com?subject=subscribe>
List-unsubscribe: <http://www.pupman.com/mailman/listinfo/tesla>, <mailto:tesla-request@pupman.com?subject=unsubscribe>
References: <50DCDA95.1070701@xxxxxxxxx> <50DE019B.5020709@xxxxxxxxxxxxxx>
Reply-to: Tesla Coil Mailing List <tesla@xxxxxxxxxx>
Sender: tesla-bounces@xxxxxxxxxx

Hi
     Yes I have a break point yes I mess with the primary too. Still no out put
at all, the 5 amp fuse side does not pull any current at all, it should pull at 
lease 3 1/2 amps.
Thanks
Alton

Sent from my iPad

On Dec 28, 2012, at 2:31 PM, Mark <the_iconoclast@xxxxxxxxxxxxxx> wrote:

> Do you have a breakout point?  Or, it could need fine tuning, mess with the turns on the primary if you haven't done so.  There are a few on Youtube you could look at, including my own.
> 
> On 12/27/2012 03:32 PM, w5als wrote:
>> Hi
>>     I am building a microbrute drsstc by eastern voltage research and i am have problems
>> and need some help. I finish it yesterday and was trying to fire it off and got nothing so by
>> the book i reverse the polarity through the current transformer that didn't work.
>> All the voltages are right check them 3 times the LED's light up, the over current led come
>> on when I ramp the PW control up. I took the board out check all solder joints and check
>> ever IC twice to make sure it was right. I tested ever diode and they were good, ever cap.
>> was check twice, I ever check the controller and wave from twice, i even compare the wave form
>> to another controller i have. I even ohm the primary and secondary out they were good.
>> Unless the IGBT are open i don't know what else it could be. Also no blown fuses neither.
>> I am not the best at this but i did have a radio/TV repair shot for 27 years so this isn't new
>> to me. I can send detail pictures if someone can compare to there's. I will thank anyone
>> for the help
>> thanks
>> alton
>> W5ALS
>> _______________________________________________
>> Tesla mailing list
>> Tesla@xxxxxxxxxx
>> http://www.pupman.com/mailman/listinfo/tesla
>> 
> 
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla

References:
- [TCML] microbrute DRSSTC
  - From: w5als
- Re: [TCML] microbrute DRSSTC
  - From: Mark

Prev by Date: Re: [TCML] microbrute DRSSTC
Next by Date: Re: [TCML] microbrute DRSSTC
Previous by thread: Re: [TCML] microbrute DRSSTC
Next by thread: Re: [TCML] microbrute DRSSTC
Index(es):
- Date
- Thread